these sweet little numbers (2 of them) were hunted down and picked up by ME from my local pier 1 imports.
all i thought was they needed a little shower under the paintbrush.
a few weeks later, i realized i had learned a lot about painting furniture. i'm here to tell you my little story so you can avoid some simple mistakes that can set your project back...
alright. let the story begin...
the piece had a few "distress" marks that were meant to add some character. this was not the look i was going for, so we i rid of that "character"
i smeared this wood filler into the mock slashes and punctures. directly after contact, i used a paster scraper to make sure to ooze the filler in as deep as it would go. i then scraped off the excess. GOOD MOVE!
next step... sand the wood filler down to even out the surface. the wood filler gives the area it touches QUITE the texture. i used some small grain sandpaper to even out the surface. GOOD MOVE!
then comes the primer. i purchased the "no sand" primer so i could avoid the most tedious part. GOOD MOVE!
i then applied this primer with a cheap roller brush that i bought from home depot. BAD NEWS... i later learned that painting furniture is best to be done with a nicer BRUSH, somewhere around the $10 mark. unlike a cheap roller, a brush will help you evenly paint your primer/paint on the surface. the roller decided to unevenly coat everything and give the surface a bubbly texture (due to the pores in the roller).
so, what did i do? ignored the problem and moved right on to painting. BAD NEWS! the paint did not solve the primer's issues. in fact, the paint did the same thing...
(note. the drawers wouldn't come out, so i just separated them like SO and painted them slowly. i thought that worked out great)
and there is some legit texture on the top surface? BAD NEWS! once again, try to get a nicer brush. instead of saving a few bucks, you'll be saving yourself MANY HOURS of correctional painting.
next big NO NO? i painted some polyurethane finish on top of the paint. since it wasn't going on evenly, i kept adding layers... and layers... and layers.
wow. all of you painters reading this must be tearing up by now. i bet you are cringing at the thought of me painting furniture...
note. polyurethane IS a protective layer, but should be used to protect wood stains. paint has a built in protective layer. the higher the gloss, the more protection. with my satin finish, i had enough built-in protection and ended up just causing myself many hours of sanding off poly layers off these bad boys.
as you can see, the higher the gloss, the worse the paint job looked...
so i tried to ignore my many problems and put in the knobs. BAD CHOICE!
don't they look a little out of proportion?
so, PLEASE CHECK THE KNOBS on your pieces BEFORE you paint! (that would be a GOOD IDEA. if not, you'll have to do what i did next...
get that woodfiller back out. we have some holes to fill and some holes to drill.
(pirctures NOT taken of the next few nasty steps. here's a summary. there was A LOT of sanding, sweeping, woodfilling, more sanding, more sweeping, some measuring, marking, and drilling... then more dusting, sweeping, wiping... then some more sanding.)
i then had the sense to buy a NICE brush ($11.49...DING DING!) and was lucky enough to have some paint left over. i then SLOWLY and CALMLY wiped the pieces down (i should have used tack cloth) and painted them evenly. here's how they turned out...
AND THEY ARE DONE!
lessons learned?
- research carefully BEFORE your project
- invest in a nicer paint brush
- paint brushes over rollers any day for painting furniture
- wood filler is magical
- it's worth fixing the problem and working on the pieces until you LOVE them
- be patient with the wood filler and paint. latex paint should actually be left alone for 24-48 hours after painting in order to let it set
- ironically, latex paint is quick to initially set, so spread your paint as evenly as possible with the brush before it sets
- get a sander! borrow from a neighbor, rent one, or buy one. it's worth your time to hunt one down. i hand sanded these pieces two separate times and was dreaming of a hand sander for days after that
- tack cloth can clean up any extra remaining particle on your furniture. please use it to wipe down your piece BEFORE priming or painting
alright. enough of my soap box.
happy painting!












I'm so sorry you had to go through all that - but you sure learned a lot! thanks for sharing.
ReplyDeletethis is so useful! thank you - I've had big dreams to paints some furniture but haven't gotten around to it - perfect motivation and tutorial right here!
ReplyDeleteI'm getting ready to paint some furniture for our girlies... thanks SO MUCH for the tips!!!
ReplyDelete